No products in the cart.
The MT3608 2A Max DC-DC Step Up Power Module Booster Power Module is a low-cost module that can step-up a 2 to 24V input voltage up to a 5 to 28V output at up to 2A. DC-DC boost converters step up the input voltage to a higher voltage while also stepping down the available current since the module can’t output more power than its inputs.₹60.00 Incl Tax₹60.00 Incl Tax
The Arduino Uno clone without cable is a microcontroller board based on the ATmega328. It has 14 digital input/output pins, 6 analogue inputs, a USB connection, a power jack. It contains everything needed to support the microcontroller; connect it to a computer with a USB cable or power it with an AC-to-DC adapter or battery to get started. Buy with USB CableBuy with USB Cable.
₹499.00Incl Tax 8% off ₹499.00Incl Tax 8% off
This HC-SR04-Ultrasonic Range Finder is a very popular sensor which is found in many applications where it requires to measure distance and detect the objects. The module has two eyes like projects in the front which forms the Ultrasonic transmitter and Receiver. The HC-SR04 ultrasonic sensor uses sonar to determine the distance to an object like bats and dolphins do.
₹110.00Incl Tax 10% off ₹110.00Incl Tax 10% off
The clone Arduino Uno with Cable is a microcontroller board based on the ATmega328. It has 14 digital input/output pins, 6 analogue inputs, a USB connection, a power jack. It contains everything needed to support the microcontroller; connect it to power with an AC-to-DC adapter or battery to get started.
- Microcontroller: atmega328.
- Operating Voltage: 5V.
- Input Voltage (Vin) : 7-12V.
₹699.00Incl Tax 29% off ₹699.00Incl Tax 29% off
NodeMcu ESP8266 Wifi development board is an edge low-cost WiFi technology. Modern high-level mature LUA based technology. It is an integrated unit with all available resources on board. It is super simple to complement your existing Arduino projects or any development board with I/O pins available. (Programmable with Arduino IDE)₹399.00 Incl Tax₹399.00 Incl Tax
It is a 5V 1 Channel With optocoupler. The relay normally open interface maximum load: AC 250V/10A, DC 30V/10A. It has a trigger current of 5mA, and module working voltage of DC 5V. Each channel of the module can be triggered by a jumper to set a high level or a low level. Fault-tolerant design, even if the control line is disconnected, the relay will not move. With status indicator: power (green), 1-channel relay status indicator (red). All module size interfaces can be directly connected through the terminal block, which is convenient and practical.₹125.00 Incl Tax₹125.00 Incl Tax
The Nano Arduino is a small, complete, and breadboard-friendly board based on the ATmega328. It has more or less the same functionality as the Uno but in a different package. It lacks only a DC power jack and works with a Mini-B USB cable instead of a standard one. It can be power via the mini-USB connection, 6-20V unregulated external power supply, or 5V regulated external power supply. The power source is automatically selected to the highest voltage source.
₹399.00Incl Tax 22% off ₹399.00Incl Tax 22% off
This Set of Aluminum Heatsink for Raspberry Pi is an aluminum heatsink kit used for cooling the chips on Raspberry Pi. Comparing to other heatsinks, it has been attached with thermally conductive adhesive tape, allowing the Raspberry Pi to cool more efficiently.₹89.00 Incl Tax₹89.00 Incl Tax
This TP4056 1A Li-Ion Battery Charging Board Micro USB with Current Protection is a tiny module, perfect for charging single cell 3.7V 1 Ah or higher lithium-ion (Li-Ion) cells such as 16550s that don’t have their own protection circuit. Based on the TP4056 charger IC and DW01 battery protection IC this module will offer 1A charge current then cut off when finished.₹80.00 Incl Tax